MiLAN MIL-S8001TG Guia do Utilizador

8-Port 10/100/1000 + 1 MiniGBIC Gigabit Ethernet Sm

6 2. Hardware Description Front Panel The Front Panel of the M

7

8 LED Indicators The LED Indicators give real-time information

9 On Orange The port is operating in Full-duplex mode. Blinks Orange Collision of Packets is occurring in the port. FDX /COL Off The port is oper

10 Rear Panel The 3-pronged power plug and console port are locate

11 Power On Connect the power cord to the power socket on the rear panel of the switch. Connect the other end of the cord to an appropriate power

12 3. Network Application This section provides you a few samples o

13 Segment Bridge For enterprise networks where large data broadcasts are constantly processed, this switch is an ideal solution for department

14 4. Console Management Connecting a Terminal or PC to the Conso

15 After the connection between the Switch and PC is finished, turn on the PC and run a terminal emulation program or Hyper Terminal and configure i

Regulatory Approval - FCC Class A - UL 1950 - CSA C22.2 No. 950 - EN60950

16 4-1. Main Menu There are five items for selection as follows. VL

17 4-2. VLAN Mode Select VLAN Mode to access the VLAN configuration menu. The system supports two VLAN modes – 802.1Q and Port-Based VLAN. At the

18 4-2-1. 802.1Q VLAN Configuration After selecting VLAN mode from the

19 4-2-1-1. Enabling 802.1Q VLAN Prior to configuring 802.1Q VLAN, the 802.1Q VLAN function must be enabled. Enter “e” or “E” at the 802.1Q VLAN men

20 4-2-1-2. VLAN Configuration The Port VID can be configured for each

21 4-2-1-3. Create VLAN Group Enter “c” or “C” at the command prompt to access the Create VLAN Group configuration interface. VLAN group ID: Enter

22 Tag/Untagged Setting: Enter “t” or “T” at the VLAN Config

23 4-2-1-4. VLAN Status VLAN Group Information can be viewed by entering “s” or “S” at the 802.1Q VLAN menu command prompt to access the VLAN Sta

24 4-2-2. Port-Based VLAN Configuration At the VLAN mode menu interfac

25 4-2-2-1. Port-Based VLAN Group Configuration A maximum of 8 VLAN groups can be configured. The default VLAN group is VLAN 1. 1. Enter the grou

Table of Contents 1. Introduction Features Software Features Packa

26 4-3. QoS Control Select QoS Control to access the QoS configuration

27 Priority ID Map: To configure the QoS control high/low weight setting, enter “m” or “M” at the command prompt. Next, enter the selection number,

28 Priority ID Map Status: To display the current priority level settin

29 4-4. Broadcast Storm Suppression Enable or disable the Broadcast storm function. In the main menu command prompt, enter command ”b” or “B” t

30 4-5. Restore to Default Enter “d” or “D” at the main menu command p

31 5. Troubleshooting This section is intended to help you solve some common problems encountered while using the MIL-S8001TG switch. Incorrect

32  Improper Network Topologies It is important to make sure that you

33 6. Technical Specifications This section provides the specifications of the MIL-S8001TG switch product. Standard IEEE 802.3 10BASE-T Ethern

34 MINI GBIC: 3.3V MINI GBIC slot shared with port #1 Back-plane 16Gbp

35 Rev A

4-4. Broadcast Storm Suppression 4-5. Restore to Default 4-6. Reset Syste

1 1. Introduction The MIL-S8001TG switch is a multi-port switch that can be used to build high-performance switched workgroup networks. This swit

2 Features  Conforms to IEEE 802.3 10BASE-T,IEEE 802.3u 10

3 Software Features VLAN Port Based VLAN, support up to 8 groups 4K IEEE802.1Q Tag VLAN QOS 2 Types of quality of service: 1.Port based priori

4 Ethernet Switching Technology Ethernet Switching Technology dra

5 Management Methods The MIL-S8001TG switch series supports Console Management methods Console Management is done through the RS-232 Console Po